Black Box Cisco HD A/D Extension Module Distribution Panel

by
BLACK BOX
PCN#
TY0869
MFG#
JPM2194A
$264.34
cps

Extended & Accidental Damage Protection Plans Available Details

  Free Shipping
Estimated Shipment:

Calculating Shipping

Product Highlights:
  • For Data Networking
  • 24 x RJ
  • 11, 8 x RJ
  • Show more

Product Condition: New and Factory Fresh
Limited WarrantyLifetime
Shipping Weight: 4 lbs.
Black Box Cisco HD A/D Extension Module Distribution Panel
Tech Specs
Specifications

Manufacturer

Black Box Corporation

Manufacturer Part Number

JPM2194A

Manufacturer Website Address

http://www.blackbox.com

Brand Name

Black Box

Product Name

Cisco HD A/D Extension Module Distribution Panel

Marketing Information

  • Designed for use with the Cisco 8-port extension module (which brings analog and digital Internet phone, fax, and modem service to Cisco 2821, 2851, 2901, 2911, 2921, 3825, 3845, 3925, 3925E, 3945, and 3945E integrated services routers).
  • With support for up to 24 total voice and fax sessions, the module is ideal for networks with high analog (foreign exchange station [FXS], direct inward dialing [DID], and foreign exchange office [FXO] and digital (Basic Rate Interface [BRI]) call-capacity requirements.
  • Three-part design includes BASE, EM0, and EM1 connectors.
  • Helps enable packet voice technologies such as Voice over IP (VoIP) by distributing digital and analog signals from legacy analog phone systems and/or Internet phones.
  • Accommodates RJ-11 and RJ-45 combinations.
  • Use telco cable (ELN29T-MF) to attach the telco connector on the back of the panel to the telco connector on the Cisco EVM-HD module that's installed in your router.
If you have a Cisco router with an 8-port voice/digital expansion module (EVM-HD) installed, consider this easy, low-cost way to connect your end analog and digital Internet phone users. The Distribution Panel for Cisco High-Density Analog and Digital Extension Module for Voice and Fax breaks out the expansion module's 50-pin telco connector into analog and digital RJ-11 and RJ-45 connectors. This simplifies how you can link end users to the Cisco module.

The panel consists of 24 RJ-11 connectors (labeled BASE) for connection to analog phones. It also has 8 RJ-45 connectors on the panel's center and right sides (labeled EM0 and EM1) for connection to digital phones, faxes, and modems. The center and right-side connectors have a sliding plate that enables you to choose either the top (RJ-11) or bottom (RJ-45) row of connectors for use. Select the connectors you will use by sliding the connector cover over the unused ports. (NOTE: You should not plug cables into the center top [RJ-11] and bottom [RJ-45] or the right-side top [RJ-11] and bottom [RJ-45] connectors at the same time. The sliding panel prevents this from happening.)

Four combinations of connectors are available, depending on which connectors are covered with the sliding plate. Link up to eight analog phones via RJ-11 cable (EL06M-MM) to the connectors labeled BASE on the panel's left side, and attach 8, 12, or 16 digital Internet phones, fax machines, or modems via RJ-11 (EL06M-MM) or RJ-45 cable (EVNSL51) to the connectors labeled EM0 or EM1 on the panel's right side.

Product Condition

New

Product Type

Expansion Module
Technical Information

Application/Usage

Data Networking
Interfaces/Ports

Total Number of Ports

9

Connector Type

  • RJ-11
  • RJ-21
  • RJ-45

Interfaces/Ports Details

  • 24 x RJ-11
  • 8 x RJ-45 LAN
  • 1 x RJ-21
Media & Performance

Media Type Supported

Twisted Pair

Twisted Pair Cable Standard

Category 5e
Physical Characteristics

Form Factor

Rack-mountable

Height

3.5"

Width

19"

Depth

1"

Weight (Approximate)

2.80 lb
Miscellaneous

Country of Origin

United States

TAA Compliant

Yes
Warranty

Limited Warranty

Lifetime
Customer Reviews